Hello Screen Setup (A12/A13)

Requirements

* USB MODULE for usbliter8
( Waveshare RP2350 USB-A / Waveshare RP2350 Zero /  Pimoroni TINY2350 / Raspberry Pi Pico 2 )

* Device with the latest supported iOS version.
* Replacement Serial number: HW0523D2Z3A

Procedure,

1. Connect the device to the tool and start the Hello service.
2. The tool will automatically reboot the device into Recovery Mode and begin the DFU process.
3. The tool will display the required serial number for Registration: (Send SN to your Favourite HFZ reseller or our HFZ Admin Team)
4. Launch USBLITER8 and use the Diagnostic function to install the new serial number.
5. Once the serial number has been written, return to the tool and start the Hello service again.
6. Wait for the activation process to complete. It usually takes around 1 minute and 30 seconds.
7. After the device reboot & already activated, click the Hello service one more time to complete the final configuration.
8. The tool will finish the process by applying the OTA Skip and Erase configuration.

( These final options can be configured through the Settings icon inside the tool )

🚀Software Benefits:
✅ Bypass your A12-A13 passcode locked / disabled Device with signal.
✅Extract Owner info.
✅iCloud Login
✅Reboot
✅App Store
✅Apple Pay
✅FaceTime
✅Notifications
✅OTA & Reset Block

🚀Supported Models🚀
- iPhone XS
- iPhone XS Max
- iPhone XR
- iPhone 11
- iPhon 11 Pro
- iPhone 11 Pro Max
- iPhone SE (2nd generation)
- iPad Air (3rd generation)
- iPad mini (5th generation)
- iPad (8th generation)
- iPad (9th generation) This model's support is currently on hold. We are trying to fix it in future updates, so stay tuned.

How to use ?

1. Connect the device in Recovery Mode
2. Run Precheck [this will detect the installed iOS version]
3. Make sure the device is on iOS 18 or iOS 26 [otherwise it is unsupported] , if lower iOS Update via 3utools first with ( Retain User's Data Option ) that will help you to update the ios version directly on Passcode/Disabled screen without going to hello screen mode.
4. Then Use DFU Helper
5. Put the device into DFU Mode
6. Run the exploit with usb module
7. Connect the device to the Mac
8. Boot the device
9. Backup Tickets
10. Do quick flash via 3utools or iTunes or factory rest [using tool]
11. Follow step 1-8
12. Restore Tickets
13. Reboot the devices and it's done.

Hardware Module Required Any:
• Waveshare RP2350 USB-A ( Best Recommended No soldering required )
• Waveshare RP2350 Zero ( Soldering Required )
• Pimoroni TINY2350 ( Soldering Required )
• Raspberry Pi Pico 2 ( Soldering Required )

✍🏻 How to use ?

0. Put apple iWatch into AWRT adapter. ( iBUS, Magic AWRT, Apple AWRT, JCID AWRT )
1. Connect iWatch in recovery mode
2. Run pre-check
3. Enter dfu
4. Pwn with *USB MODULE* (RP2350)
5. Boot ramdisk with "Boot" button
6. Wait until screen shows verbose boot and you see mount done
7. Then click activate
8. Success

( If device quit black screen before success, maybe mount failed. most likely bad version, need update first. Can be done even if locked device )

Hardware Module Required Any:
• Waveshare RP2350 USB-A ( Best Recommended No soldering required )
• Waveshare RP2350 Zero ( Soldering Required )
• Pimoroni TINY2350 ( Soldering Required )
• Raspberry Pi Pico 2 ( Soldering Required )

How to use ?
- Restore device with latest firmware via 3utools or iTunes. (recommended)
- Register device via serial number.
- Activate the device with tool without connecting to Wi-Fi.
    ~ done ✅