In chain surveying, sag correction is always
Anonymous Quiz
15%
Positive
75%
Negative
10%
Either is possible
Which of the following methods of plan table surveying is used to locate the position of an inaccessible points?
Anonymous Quiz
7%
Radiation
56%
Intersection
17%
Traversing
20%
Resection
S-hydrograph is used to obtain unit Hydrograph of
Anonymous Quiz
24%
Shorter duration from longer duration
37%
Longer duration from shorter duration
39%
Both
Discharge per unit drawdown of a well is called
Anonymous Quiz
30%
Specific yield
15%
Specific retention
48%
Specific capacity
8%
Specific storage
Performance of a well is measured by its
Anonymous Quiz
22%
Specific yield
32%
Specific capacity
10%
Storage co-efficient
37%
All of above
Specific capacity of a well
Anonymous Quiz
8%
Decreases with diameter
55%
Decreases with time from the start of pumping
29%
Increases with discharge rate
8%
None of these
Water in an unconfined well
Anonymous Quiz
39%
Increases with increase in the atmospheric pressure
26%
Decreases with decrease in the atmospheric pressure
34%
Does not affected by atmospheric pressure
Spire test is used for adjustment of
Anonymous Quiz
14%
Line of sight
45%
Horizontal axis
10%
Vertical axis
31%
Adjustment of altitude bubble
Which of the following may not be classified as personal error?
Anonymous Quiz
2%
Inaccurate centering
10%
Inaccurate levelling
71%
Plane of sight not being vertical
17%
Carelessness in reading and recording
A 10 cm theodolite means that
Anonymous Quiz
10%
Length of its telescope is 10 cm
53%
Diameter of the graduated circle of its lower plate is 10 cm
22%
Diameter of the graduated circle of its vertical circle is 10 cm
2%
Diameter of the graduated circle of its upper plate is 10 cm
14%
Focal length of objective glass is 10 cm
Reciprocal levelling eliminates
Anonymous Quiz
28%
Error due to curvature and refraction
8%
Collimation error
62%
Both
2%
None of these
Contour lines are perpendicular to the
Anonymous Quiz
33%
Ridge lines
22%
Valley lines
38%
Both of above
7%
None of these
Rise and fall method of levelling provides a complete check on
Anonymous Quiz
2%
Back sight
5%
Fore sight
18%
Intermediate sight
75%
All of the above
Fix of a plane table from three known point is good if
Anonymous Quiz
22%
Middle station is the nearest
44%
Middle station is farther than the other two stations
18%
Either of the extreme station is the nearest
16%
Middle station is close to the great circle
In Column Splices should be provided at
Anonymous Quiz
3%
floor level
24%
mid height of column
16%
beam-column joints
57%
one fourth height of column
The height at which wind force acting on a moving vehicle on bridge deck is
Anonymous Quiz
32%
1.2 m
55%
1.5 m
11%
1.7 m
2%
2 m
Generally for structural steel connections, the process of welding adopted is
Anonymous Quiz
11%
Carbon Arc Welding
40%
Oxy-hydrogen welding
46%
metal arc welding
3%
pressure welding
In the fillet weld, the weakest section is
Anonymous Quiz
4%
Smaller size of fillet
73%
throat of the fillet
17%
Side perpendicular to force
6%
side parallel to force
Which of the following section is preferably be used at places where torsion occurs?
Anonymous Quiz
14%
Angle Section
38%
Box Section
19%
Channel Section
29%
Circular Section
https://civilenggascent.com/autodesk-revit-vs-graphisoft-archicad-key-differences-in-bim-tools/
AutoDesk Revit vs Graphisoft Archicad
AutoDesk Revit vs Graphisoft Archicad
Civil Engineering Ascent
Autodesk Revit vs Graphisoft Archicad – Key Differences in BIM Tools - Civil Engineering Ascent
Autodesk Revit vs Graphisoft Archicad – Compare Features Autodesk Revit vs Graphisoft Archicad comparison is one of the most consequential decisions an architecture or engineering firm makes. It shapes how you model, document, coordinate with consultants…