This media is not supported in your browser
VIEW IN TELEGRAM
🎚 LilyGO T-PicoC3 board merges RP2040 & ESP32-C3, integrates color display
LilyGO T-PicoC3 is a small development board combining Raspberry Pi RP2040 dual-core microcontroller with ESP32-C3 RISC-V MCU to add WiFi and Bluetooth LE connectivity and adds a 1.14-inch color display to the mix, plus several I/Os.
Specifications:
▫️ Raspberry Pi RP2040 dual-core Cortex-M0+ MCU with 264 KB of embedded SRAM
▫️ Espressif Systems ESP32-C3 RISC-V processor with WiFi 4 and Bluetooth 5.0 LE connectivity
▫️ Storage – 4MB SPI flash connected to RP2040
▫️ Display – 1.14-inch full-color IPS LCD Display (ST7789V SPI controller) with 240 x 135 resolution
Both the Raspberry Pi RP2040 and ESP32-C3 microcontroller are programmable, and interestingly the Tx/Rx connection is decided by the orientation of the USB Type-C connector: A side is for RP2040 (Blue LED on) and B side (Green LED on) is for ESP32-C3.
#boards #esp32 #raspberry
LilyGO T-PicoC3 is a small development board combining Raspberry Pi RP2040 dual-core microcontroller with ESP32-C3 RISC-V MCU to add WiFi and Bluetooth LE connectivity and adds a 1.14-inch color display to the mix, plus several I/Os.
Specifications:
▫️ Raspberry Pi RP2040 dual-core Cortex-M0+ MCU with 264 KB of embedded SRAM
▫️ Espressif Systems ESP32-C3 RISC-V processor with WiFi 4 and Bluetooth 5.0 LE connectivity
▫️ Storage – 4MB SPI flash connected to RP2040
▫️ Display – 1.14-inch full-color IPS LCD Display (ST7789V SPI controller) with 240 x 135 resolution
Both the Raspberry Pi RP2040 and ESP32-C3 microcontroller are programmable, and interestingly the Tx/Rx connection is decided by the orientation of the USB Type-C connector: A side is for RP2040 (Blue LED on) and B side (Green LED on) is for ESP32-C3.
#boards #esp32 #raspberry
👍5👎1
📟 OBJEX Link - open-source development board based on ESP32
OBJEX Link is a modular IoT board. It is designed to develop IoT devices that are easy to repair and recycle. OBJEX Link is designed to meet a wide range of uses: Smart Home & Cities, IIOT, Everyday things & Wearables, Predictive Maintenance, Agriculture Automation.
OBJEX Link can also be used for rapid prototyping, and developing research and robotics projects, with the right module you can extend the possible uses of the board.
The compact form factor and board design ensure easy use and maintenance of the board. The architecture of OBJEX Link is composed of two parts, the first is the mainboard (OBJEX Link) and the second is the module allows for easy customization and interfacing with hardware compared to other IoT boards.
More information:
GitHub page
Documentation page
#projects #boards #esp32
OBJEX Link is a modular IoT board. It is designed to develop IoT devices that are easy to repair and recycle. OBJEX Link is designed to meet a wide range of uses: Smart Home & Cities, IIOT, Everyday things & Wearables, Predictive Maintenance, Agriculture Automation.
OBJEX Link can also be used for rapid prototyping, and developing research and robotics projects, with the right module you can extend the possible uses of the board.
The compact form factor and board design ensure easy use and maintenance of the board. The architecture of OBJEX Link is composed of two parts, the first is the mainboard (OBJEX Link) and the second is the module allows for easy customization and interfacing with hardware compared to other IoT boards.
More information:
GitHub page
Documentation page
#projects #boards #esp32
👍14
📟 ESP32 board with 150Mbps 4G LTE modem also supports RS485, CAN Bus, and relay expansion
LILYGO has designed another ESP32 board with a 4G LTE modem delivering up to 150 Mbps download and 50 Mbps upload speeds.
The board also supports GPS, includes a 18650 battery holder, and features I/O expansion headers that support an add-on board with RS485 and CAN bus interfaces, but no cellular connectivity.
Board specifications:
▫️ ESP32-WROVER-E module based on ESP32 dual-core processor @ 240 MHz with 4MB flash, 8MB PSRAM, 2.4 GHz WiFi 4 and Bluetooth 4.2/5.x connectivity, PCB antenna
▫️ Nano-SIM card socket, 1x external 4G LTE antenna (but 2x u.FL antenna connectors)
▫️ Expansion – 2x 16-pin headers with GPIOs, ADC, DAC, touch interface, UART, I2C, SPI, VN/VP, Reset, VBUS, VBAT, 3.3V, GND
More information...
#boards #esp32
LILYGO has designed another ESP32 board with a 4G LTE modem delivering up to 150 Mbps download and 50 Mbps upload speeds.
The board also supports GPS, includes a 18650 battery holder, and features I/O expansion headers that support an add-on board with RS485 and CAN bus interfaces, but no cellular connectivity.
Board specifications:
▫️ ESP32-WROVER-E module based on ESP32 dual-core processor @ 240 MHz with 4MB flash, 8MB PSRAM, 2.4 GHz WiFi 4 and Bluetooth 4.2/5.x connectivity, PCB antenna
▫️ Nano-SIM card socket, 1x external 4G LTE antenna (but 2x u.FL antenna connectors)
▫️ Expansion – 2x 16-pin headers with GPIOs, ADC, DAC, touch interface, UART, I2C, SPI, VN/VP, Reset, VBUS, VBAT, 3.3V, GND
More information...
#boards #esp32
👍10
Fast cores, large memory, and flexible interfacing make RP2040 a natural building block for Internet of Things (IoT) applications. But Pico itself has one obvious missing feature for IoT: a method for connecting to the network. Now, this is about to change.
Raspberry Pi Pico W is priced at $6, and brings 802.11n wireless networking to the Pico platform, while retaining complete pin compatibility with its older sibling.
Like the original Raspberry Pi Pic, the new board supports both C programming and MicroPython, but the Raspberry Pi Pico W comes preloaded with MicroPython. Programming is about the same, except for the additional Wi-Fi API.
#boards #raspberry
Please open Telegram to view this post
VIEW IN TELEGRAM
Please open Telegram to view this post
VIEW IN TELEGRAM
👍7
🎚 EdgePro1 - tiny, open-source, 600-MHz, ARM-Cortex-M7 board with Wi-Fi & BLE connectivity and LuaJIT support
EdgePro1 is all about power and simplicity. The board was designed to fit between low-level microcontroller boards (think Arduino style) and full fledged Linux capable Single-Board-Computers or SBCs.
It is an IoT capable device with WiFi/BLE communication, some external storage (8 MB - mega bytes of it) and of course a security chip to protect sensitive data going in and out.
Main CPU is NXP i. MX RT1064 with 600 MHz Cortex M7, 4 MB of XiP Flash and 1 MB of static RAM, which includes a 512 KB of Tightly-Coupled-Memory (TCM). Later is capable of running at CPU speeds without the use of cache memory. The U-Blox Nina W102 communication module has additional two Tensilica 240 MHz cores together with 520 KB of RAM and 2 MB of Flash.
More information...
#boards
EdgePro1 is all about power and simplicity. The board was designed to fit between low-level microcontroller boards (think Arduino style) and full fledged Linux capable Single-Board-Computers or SBCs.
It is an IoT capable device with WiFi/BLE communication, some external storage (8 MB - mega bytes of it) and of course a security chip to protect sensitive data going in and out.
Main CPU is NXP i. MX RT1064 with 600 MHz Cortex M7, 4 MB of XiP Flash and 1 MB of static RAM, which includes a 512 KB of Tightly-Coupled-Memory (TCM). Later is capable of running at CPU speeds without the use of cache memory. The U-Blox Nina W102 communication module has additional two Tensilica 240 MHz cores together with 520 KB of RAM and 2 MB of Flash.
More information...
#boards
👍10👎1
🎚 Bee S3 ultra-low-power ESP32-S3 board can last several years on a LiPo battery
Smart Bee Designs’ Bee S3 is an ultra-low-power development board based on Espressif ESP32-S3 WiFi & Bluetooth microcontroller that consumes less than 20 uA in deep sleep mode allowing the board to theoretically last over 5 years under specific conditions.
Bee S3 specifications:
▫️ Wireless module – Espressif Systems ESP32-S3-MINI-1 module with ESP32-S3 dual-core Xtensa LX7 processor with WiFi 4 and Bluetooth 5.0 connectivity, 4MB or 8MB QSPI flash, PCB antenna
▫️ Expansion – 2x 10-pin headers with up to 15x GPIO, 8x ADC, touch support, I2C, SPI, UART, 5V In/out, 3.3V out, and GND
▫️ Misc – Reset and Boot buttons, RGB LED
▫️ Support for 1S LiPo battery through 2-pin JST connector with battery voltage monitoring
Power consumption:
▫️ Deep sleep – < 20 uA
▫️ Wake, no WiFi – 40 mAh
▫️ Wi-Fi Connected, no traffic – 55+ mAh
▫️ Sending/receiving MQTT messages – 100 mAh
#boards
Smart Bee Designs’ Bee S3 is an ultra-low-power development board based on Espressif ESP32-S3 WiFi & Bluetooth microcontroller that consumes less than 20 uA in deep sleep mode allowing the board to theoretically last over 5 years under specific conditions.
Bee S3 specifications:
▫️ Wireless module – Espressif Systems ESP32-S3-MINI-1 module with ESP32-S3 dual-core Xtensa LX7 processor with WiFi 4 and Bluetooth 5.0 connectivity, 4MB or 8MB QSPI flash, PCB antenna
▫️ Expansion – 2x 10-pin headers with up to 15x GPIO, 8x ADC, touch support, I2C, SPI, UART, 5V In/out, 3.3V out, and GND
▫️ Misc – Reset and Boot buttons, RGB LED
▫️ Support for 1S LiPo battery through 2-pin JST connector with battery voltage monitoring
Power consumption:
▫️ Deep sleep – < 20 uA
▫️ Wake, no WiFi – 40 mAh
▫️ Wi-Fi Connected, no traffic – 55+ mAh
▫️ Sending/receiving MQTT messages – 100 mAh
#boards
👍5
📃 Raspberry Pi Pico Variants – A Detailed Comparison
Raspberry Pi Pico is a low-cost, versatile microcontroller development board from the Raspberry pi foundation. Let’s look at all these variants and their differences.
▫️ Raspberry Pi Pico is the first low-cost Microcontroller development board from the infamous Raspberry Pi Foundation.
▫️ Pico H is the same as the original Raspberry Pi Pico. There are no functional differences between them. The main difference is that the old gold-plated castellated holes are removed, and the header pins are pre-soldered. Another major difference is the new debug connector. The original Pico has a 2.54mm standard header pi for the debug.
▫️ Even though the Raspberry Pi Pico is a very powerful board, its main disadvantage over its competitors like ESP8266 or ESP32 is the lack of wireless connectivity. The new Pico W and WH have the solution for that. The new Pico W comes with a new chip supports both 2.4 GHz WiFi 4 and Bluetooth LE 5.2.
#articles #boards
Raspberry Pi Pico is a low-cost, versatile microcontroller development board from the Raspberry pi foundation. Let’s look at all these variants and their differences.
▫️ Raspberry Pi Pico is the first low-cost Microcontroller development board from the infamous Raspberry Pi Foundation.
▫️ Pico H is the same as the original Raspberry Pi Pico. There are no functional differences between them. The main difference is that the old gold-plated castellated holes are removed, and the header pins are pre-soldered. Another major difference is the new debug connector. The original Pico has a 2.54mm standard header pi for the debug.
▫️ Even though the Raspberry Pi Pico is a very powerful board, its main disadvantage over its competitors like ESP8266 or ESP32 is the lack of wireless connectivity. The new Pico W and WH have the solution for that. The new Pico W comes with a new chip supports both 2.4 GHz WiFi 4 and Bluetooth LE 5.2.
#articles #boards
👍5
🎚 Unexpected Maker TinyS3, FeatherS3 and ProS3 boards feature ESP32-S3 dual-core wireless MCU
Seon Rozenblum, better known as Unexpected Maker, has launched upgrades to its ESP32-S2 boards such as the TinyS2 with ESP32-S3 variants, namely TinyS3, FeatherS3, and ProS3 boards.
The new boards share the same form factors as the TinyS2, FeatherS2, and ProS2, but they get a more powerful dual-core microcontroller with AI instructions and 512kB SRAM. The microcontroller also adds Bluetooth 5.0 Low Energy (BLE) connectivity with Bluetooth Mesh support, instead of just WiFi 4 connectivity found in the earlier boards.
The boards are compatible with CircuitPython, MicroPython, the ESP-IDF, the Arduino IDE, and other coding platforms, but the getting started guide focuses on the CircuitPython firmware which comes pre-installed in the ESP32-S3 boards. The PDF schematics, KiCad 6 footprints and symbols, and 3D models can be found on GitHub.
More information...
#boards
Seon Rozenblum, better known as Unexpected Maker, has launched upgrades to its ESP32-S2 boards such as the TinyS2 with ESP32-S3 variants, namely TinyS3, FeatherS3, and ProS3 boards.
The new boards share the same form factors as the TinyS2, FeatherS2, and ProS2, but they get a more powerful dual-core microcontroller with AI instructions and 512kB SRAM. The microcontroller also adds Bluetooth 5.0 Low Energy (BLE) connectivity with Bluetooth Mesh support, instead of just WiFi 4 connectivity found in the earlier boards.
The boards are compatible with CircuitPython, MicroPython, the ESP-IDF, the Arduino IDE, and other coding platforms, but the getting started guide focuses on the CircuitPython firmware which comes pre-installed in the ESP32-S3 boards. The PDF schematics, KiCad 6 footprints and symbols, and 3D models can be found on GitHub.
More information...
#boards
👍6
🎚 $6 Pine64 Ox64 SBC features BL808 64-bit/32-bit RISC-V multi-protocol WiSoC with 64MB RAM
Pine64 Ox64 is a single board computer powered by Bouffalo Lab BL808 dual-core 64-bit/32-bit RISC-V processor with up to 64MB embedded RAM, multiple radios for WiFi 4, Bluetooth 5.0, and 802.15.4 (Zigbee), as well as an AI accelerator.
The board also features up to 16MB XSPI NOR flash, a MicroSD card socket, a USB 2.0 OTG port with support for a 2-lane MIPI CSI camera module, and two 20-pin GPIO headers for expansion. It measures just 51 x 21mm, or in other words, is about the size of a Raspberry Pi Pico W.
The BL808 wireless processor is designed for low-power AIoT video/audio applications, notably two-way voice intercoms. The BL808 is supported by an RTOS SDK, and Linux is being worked on. That’s why there are two SKUs for the Ox64 board, one with 16Mbit flash suitable to run an RTOS and another one with 128 Mbit flash to run Linux.
#boards
Pine64 Ox64 is a single board computer powered by Bouffalo Lab BL808 dual-core 64-bit/32-bit RISC-V processor with up to 64MB embedded RAM, multiple radios for WiFi 4, Bluetooth 5.0, and 802.15.4 (Zigbee), as well as an AI accelerator.
The board also features up to 16MB XSPI NOR flash, a MicroSD card socket, a USB 2.0 OTG port with support for a 2-lane MIPI CSI camera module, and two 20-pin GPIO headers for expansion. It measures just 51 x 21mm, or in other words, is about the size of a Raspberry Pi Pico W.
The BL808 wireless processor is designed for low-power AIoT video/audio applications, notably two-way voice intercoms. The BL808 is supported by an RTOS SDK, and Linux is being worked on. That’s why there are two SKUs for the Ox64 board, one with 16Mbit flash suitable to run an RTOS and another one with 128 Mbit flash to run Linux.
#boards
👍6
🎛 XIAO ESP32S3 is a tiny ESP32-S3 WiFi 4 and BLE 5.0 module for IoT, AI, and robotics
XIAO ESP32S3 is an ESP32-S3 dual-core wireless microcontroller with WiFi 4 and BLE 5.0 designed for Smart Home, IoT, wearables, and Robotics applications.
It succeeds the single-core ESP32-C3-based XIAO ESP32C3 board with the same form factor, but the new XIAO ESP32S3 offers more performance, vector extension for machine learning, more flash, and improved power consumption in deep sleep mode.
Specifications:
▫️ Wireless MCU: ESP32-S3R8 dual-core Tensilica LX7 microcontroller @ 240 MHz with 512KB SRAM, 8MB PSRAM, Wi-Fi 4 & Bluetooth 5.0 dual-mode (Classic + BLE) connectivity
▫️ Storage: 8MB SPI flash
▫️ Expansion I/Os: 2x 7-pin headers with 1x UART, 1x I2C, 1x SPI, 11x GPIO (PWM), 9x ADC 3.3V I/O voltage (not 5V tolerant)
More information...
#boards #esp32
XIAO ESP32S3 is an ESP32-S3 dual-core wireless microcontroller with WiFi 4 and BLE 5.0 designed for Smart Home, IoT, wearables, and Robotics applications.
It succeeds the single-core ESP32-C3-based XIAO ESP32C3 board with the same form factor, but the new XIAO ESP32S3 offers more performance, vector extension for machine learning, more flash, and improved power consumption in deep sleep mode.
Specifications:
▫️ Wireless MCU: ESP32-S3R8 dual-core Tensilica LX7 microcontroller @ 240 MHz with 512KB SRAM, 8MB PSRAM, Wi-Fi 4 & Bluetooth 5.0 dual-mode (Classic + BLE) connectivity
▫️ Storage: 8MB SPI flash
▫️ Expansion I/Os: 2x 7-pin headers with 1x UART, 1x I2C, 1x SPI, 11x GPIO (PWM), 9x ADC 3.3V I/O voltage (not 5V tolerant)
More information...
#boards #esp32
👍6👎1
🎛 $25 Sipeed Tang Nano 20K FPGA board can simulate a RISC-V core, run Linux, retro games
The Sipeed Tang Nano 20K is a low-cost FPGA development board based on Gowin GW2AR-18 FPGA with 20,736 logic cells and 64Mbit RAM, which coupled with 64MBit QSPI flash provides enough resources to simulate a 32-bit RISC-V core booting Linux or playing retro games in an emulator.
The FPGA board comes with a USB-C port for power and to load the FPGA bitstream through a BL616 microcontroller that also acts as a USB to serial chip, an HDMI port and an RGB LCD interface for video output, two user buttons, and two rows GPIOs to connect peripherals such as gamepads (through adapters).
More information...
#boards #fpga
The Sipeed Tang Nano 20K is a low-cost FPGA development board based on Gowin GW2AR-18 FPGA with 20,736 logic cells and 64Mbit RAM, which coupled with 64MBit QSPI flash provides enough resources to simulate a 32-bit RISC-V core booting Linux or playing retro games in an emulator.
The FPGA board comes with a USB-C port for power and to load the FPGA bitstream through a BL616 microcontroller that also acts as a USB to serial chip, an HDMI port and an RGB LCD interface for video output, two user buttons, and two rows GPIOs to connect peripherals such as gamepads (through adapters).
More information...
#boards #fpga
👍9
📰 The Arduino has just introduced Nano ESP32
The Arduino Nano ESP32 is an ESP32-S3-based Wi-Fi and Bluetooth microcontroller board designed for IoT applications for hobbyists and enterprise use cases. The new Nano board comes with 8 MB PSRAM and 16 MB flash storage and can be programmed with either the Arduino or MicroPython languages.
Key features of the board:
▫️ Tiny size: Perfect for embedding in standalone projects, designed with a compact Nano form factor.
▫️ Wi-Fi and Bluetooth: Powered by the ESP32-S3 microcontroller, offering wireless connectivity with full Arduino support.
▫️ Arduino IoT Cloud compatibility: Create IoT projects effortlessly using the Arduino IoT Cloud app.
▫️ HID support: Emulate keyboards or mice over USB, expanding computer interaction possibilities.
More information...
#news #boards #arduino #esp32
The Arduino Nano ESP32 is an ESP32-S3-based Wi-Fi and Bluetooth microcontroller board designed for IoT applications for hobbyists and enterprise use cases. The new Nano board comes with 8 MB PSRAM and 16 MB flash storage and can be programmed with either the Arduino or MicroPython languages.
Key features of the board:
▫️ Tiny size: Perfect for embedding in standalone projects, designed with a compact Nano form factor.
▫️ Wi-Fi and Bluetooth: Powered by the ESP32-S3 microcontroller, offering wireless connectivity with full Arduino support.
▫️ Arduino IoT Cloud compatibility: Create IoT projects effortlessly using the Arduino IoT Cloud app.
▫️ HID support: Emulate keyboards or mice over USB, expanding computer interaction possibilities.
More information...
#news #boards #arduino #esp32
👍12👎3
The Orange Pi Zero 2W offers a compelling alternative to the Raspberry Pi Zero 2W, closely matching its form factor while delivering notable upgrades in performance and versatility. With its Allwinner H618 quad-core Cortex-A53 processor clocked at 1.5 GHz and RAM options ranging from 1 to 4GB, it provides enhanced computing power.
Key features include a mini HDMI port, dual USB-C ports, Wi-Fi 5, Bluetooth 5.0, and a 16MB SPI flash for bootloader storage. It retains compatibility with the Raspberry Pi's 40-pin GPIO header and introduces a 24-pin "function" connector for expansion boards. The board supports multiple operating systems, including Debian and Ubuntu.
An optional expansion board enhances functionality with more ports and receivers. The starting price of $12.9 for the 1GB RAM variant making it an attractive choice for those looking for an affordable and powerful single-board computer.
#boards #orange
Please open Telegram to view this post
VIEW IN TELEGRAM
👍14
This small but mighty single board computer is powered by a high-performance quad-core processor and offers various connectivity options, including full-size HDMI 2.0 and gigabit Ethernet. In addition to that, the board includes a unique design featuring a carrier board and a replaceable LM3H CPU module containing the SoC, RAM, and eMMC flash.
Key Specifications:
Sipeed provides Debian and Android 12 images for the board, with SDKs available on GitHub. Mainline Linux support is expected in Q1 2024. Sipeed has begun pre-orders on Aliexpress, with prices ranging from $23.90 (2GB RAM, no eMMC flash) to $34.90 (4GB RAM and 32GB eMMC flash), and the LM3H module alone starting at $17.90. Shipping is expected to start on February 11.
#boards
Please open Telegram to view this post
VIEW IN TELEGRAM
👍14👌1
Meet NanoS3, the epitome of compact power in the world of development boards. At a mere 28 x 11mm, this ESP32-S3 module redefines versatility and performance, packing a punch with its dual 32-bit Xtensa LX7 cores running at up to 240MHz, complemented by a RISC-V Ultra Low Power Co-processor.
Features of the board:
With a UF2 bootloader and pre-installed CircuitPython, firmware updates are hassle-free. Whether you prefer MicroPython, ESP-IDF, or Arduino IDE, NanoS3 supports your preferred programming environment.
Explore the special repository, offering 3D STEP files, KiCAD symbols and footprints, reference designs, schematics, and pinout cards. NanoS3 empowers makers, innovators, and enthusiasts to dream big in a compact footprint.
More information:
#boards #esp32
Please open Telegram to view this post
VIEW IN TELEGRAM
👍19👌2
This newly released development board, powered by the BG95-M3 Zero module, is a cutting-edge platform designed specifically for cellular IoT development. With its robust features and versatile design, it offers a streamlined approach to building and testing IoT applications.
Features of the board:
The BG95 EVB Development Board offers a compelling solution for IoT prototyping, combining versatility, user-friendliness, and extensive protocol support.
#news #boards
Please open Telegram to view this post
VIEW IN TELEGRAM
👍11👌1
The Signaloid C0-microSD is an innovative FPGA development board, fitting within a standard microSD card socket for easy programming. It leverages a unique interface and supports cloud and edge-based computing applications.
Features of the board:
This board is ideal for developers seeking a compact, versatile platform for FPGA prototyping. Its microSD form factor and onboard processing capabilities make it suitable for both hobbyists and professionals looking to enhance single-board computers or microcontrollers with advanced computing features.
More information:
#boards #fpga
Please open Telegram to view this post
VIEW IN TELEGRAM
Please open Telegram to view this post
VIEW IN TELEGRAM
👍15👌2
Embedded Systems
This microcontroller is an enhanced version of the popular Raspberry Pi Pico 2 microcontroller, featuring integrated Wi-Fi capabilities. Developed by Pimoroni, this board builds upon the Pico 2 platform by incorporating the "Raspberry Pi RM2" module for wireless connectivity, marking a significant upgrade for IoT and embedded projects.
Features of the microcontroller:
With ample memory and a robust set of connectivity options, it's well-suited for IoT applications, data logging, and remote monitoring projects. The addition of the Clipper LTE 4G breakout board expands its utility further, offering cellular connectivity for applications that require reliable data transmission in areas without Wi-Fi coverage.
#boards #raspberry #IoT
Please open Telegram to view this post
VIEW IN TELEGRAM
👍11
Embedded Systems
The Raspberry Pi Compute Module 5 (CM5) brings the power of
Key features of the board:
Cooling can be a challenge—passive solutions suffice for standard tasks, but overclocking requires better thermal management than the current active cooling setup offers.
Designed for embedded projects, the CM5 starts at $45 and is a powerful tool for makers and professionals seeking scalable, customizable solutions. Those with simpler needs may prefer the standard Raspberry Pi 5.
#boards #raspberry
Please open Telegram to view this post
VIEW IN TELEGRAM
👍8👌1
The Waveshare ESP32-C6-Touch-AMOLED-1.8 is a compact development board built around
Key features of the board:
Overall, this development board stands out as a highly integrated, display-centric ESP32-C6 platform. It would be especially interesting for developers working on smart home panels, wearable or handheld IoT devices and portable dashboards.
#boards #esp32
Please open Telegram to view this post
VIEW IN TELEGRAM
👌9👍1